All this stuff, and more will be at Kentucky this weekend. Part of a complete sell out. I have not had time to price anything, just wanted to give a heads up that this stuff will be there. Parts are used unless otherwise stated.
New 33" x 1 1/4 rear axle .187 wall
New 34" " " " "
New 34" " " " .250 wall
Used 34" " " " "
MCP rear brake caliper
Set of MCP front brakes
Set of MCP front brakes w/MC
2- New Master Cylinders
4- New Master Cylinder Rebuild Kits
3 sets- New MCP Rear Brake Pads (Black)
2- sets- New MCP front Brake Pads (blue)
1- barely used Piere Haung (sp?) front brake pads for mcp
2- New Rear brake mounts
1- Complete Hagar Front Brake Set w/extra caliper
1- set of front hubs with rotors
1 set- New MCP thick (.183) Front brake Rotors
2- New Brake Rotor mounts
4- New Rear Wheel Hubs
2- New Steering Shaft Hubs
New Yam Carb in box
3- New bearing cassettes
4- Used "" "
2- Enduro headrests
1- New Fuel sump tank
1- New Enduro fuel tank nozzle
5- New throttle cables
3- carb trigger assemblies
1- carb trigger rope
1- complete Mychron II unit... Barely used
1- New Kart Push Stick
1- Rolling Starter carriage.. Start your own kart
4- Pipe mounts
1- New Sportsman pipe
Various motor plates mostly for Yamaha, one used once for reed jet.
All kinds of of both 20mm and 30mm front drivers.
30mm rear sprockets: 68, 72, and 82(new)
20mm rear sprockets: 67, 74, 79(new), 80(new), 81, 82, 83, 84, 85, 86, 87, 90
1- Horstman Enduro Axle Clutch. Has not been run since freshened, Oil spilled on the paper that had all the details. All that is readable is Springs: .831, .833, .832, .833, .833, and .833. Pressure Plate .147, and air gap is set at .047.... 2-turns out. As far as the floater and friction disc #'s, they are lost to he oil on the paper. I can tell you this though. I had about 7 Horstman Clutches, and this was the 1 I kept.
4- pkgs of new horstman springs
3- new friction discs,
1- Horstman 1 1/4 Axle Clutch Hub. New Pressure Plate, nice floaters, and a slew of other Horstman Axle Clutch stuff
1- SMC Axle Clutch (#3197), not run since freshened by MGP Racing (see pic)
A separate box of all kinds of SMC Axle Clutch parts!
Longacre Scale Set. Cannot get battery to work, but works fine off of plug in. It is missing the 1 1/8 tube to hold up the stands... We never used the stands, just a flat surface.
Plus plenty more.
Again, I have not had time to price anything. So basically, if you make a REASONABLE offer, it will be yours!
Pics can be seen here: https://www.dropshots.com/Crankin/albums/501043
New 33" x 1 1/4 rear axle .187 wall
New 34" " " " "
New 34" " " " .250 wall
Used 34" " " " "
MCP rear brake caliper
Set of MCP front brakes
Set of MCP front brakes w/MC
2- New Master Cylinders
4- New Master Cylinder Rebuild Kits
3 sets- New MCP Rear Brake Pads (Black)
2- sets- New MCP front Brake Pads (blue)
1- barely used Piere Haung (sp?) front brake pads for mcp
2- New Rear brake mounts
1- Complete Hagar Front Brake Set w/extra caliper
1- set of front hubs with rotors
1 set- New MCP thick (.183) Front brake Rotors
2- New Brake Rotor mounts
4- New Rear Wheel Hubs
2- New Steering Shaft Hubs
New Yam Carb in box
3- New bearing cassettes
4- Used "" "
2- Enduro headrests
1- New Fuel sump tank
1- New Enduro fuel tank nozzle
5- New throttle cables
3- carb trigger assemblies
1- carb trigger rope
1- complete Mychron II unit... Barely used
1- New Kart Push Stick
1- Rolling Starter carriage.. Start your own kart
4- Pipe mounts
1- New Sportsman pipe
Various motor plates mostly for Yamaha, one used once for reed jet.
All kinds of of both 20mm and 30mm front drivers.
30mm rear sprockets: 68, 72, and 82(new)
20mm rear sprockets: 67, 74, 79(new), 80(new), 81, 82, 83, 84, 85, 86, 87, 90
1- Horstman Enduro Axle Clutch. Has not been run since freshened, Oil spilled on the paper that had all the details. All that is readable is Springs: .831, .833, .832, .833, .833, and .833. Pressure Plate .147, and air gap is set at .047.... 2-turns out. As far as the floater and friction disc #'s, they are lost to he oil on the paper. I can tell you this though. I had about 7 Horstman Clutches, and this was the 1 I kept.
4- pkgs of new horstman springs
3- new friction discs,
1- Horstman 1 1/4 Axle Clutch Hub. New Pressure Plate, nice floaters, and a slew of other Horstman Axle Clutch stuff
1- SMC Axle Clutch (#3197), not run since freshened by MGP Racing (see pic)
A separate box of all kinds of SMC Axle Clutch parts!
Longacre Scale Set. Cannot get battery to work, but works fine off of plug in. It is missing the 1 1/8 tube to hold up the stands... We never used the stands, just a flat surface.
Plus plenty more.
Again, I have not had time to price anything. So basically, if you make a REASONABLE offer, it will be yours!
Pics can be seen here: https://www.dropshots.com/Crankin/albums/501043